Meinberg Radio Clocks LANTIME M-Series XSS
All information products included in http://ics-cert.us-cert.gov are provided "as is" for informational purposes only. The Department of Homeland Security (DHS) does not provide any warranties of any kind regarding any information contained within. DHS does not endorse any commercial product or service, referenced in this product or otherwise. Further dissemination of this product is governed by the Traffic Light Protocol (TLP) marking in the header. For more information about TLP, see http://www.us-cert.gov/tlp/.
This advisory was originally posted to the US-CERT secure Portal library on October 2, 2014, and is being released to the ICS-CERT web site.
Martem Telecontrol Systems security researcher Aivar Liimets has identified a reflected cross‑site scripting vulnerability in the Meinberg Radio Clocks GmbH & Co. KG LANTIME M400 web interface. Meinberg has produced a firmware update that mitigates this vulnerability in all LANTIME M-Series. Aivar Liimets has tested the firmware update to validate that it resolves the vulnerability.
This vulnerability could be exploited remotely.
The following Meinberg Network Time Protocol (NTP) Server firmware versions are affected:
- LANTIME M-Series models: V6.15.019 and prior.
The reflected cross-site scripting vulnerability could cause the time server to provide misinformation to devices.
Impact to individual organizations depends on many factors that are unique to each organization. ICS-CERT recommends that organizations evaluate the impact of this vulnerability based on their operational environment, architecture, and product implementation.
Meinberg Radio Clocks GmbH & Co. KG is an international provider of electronic modules, based in Bad Pyrmont, Germany.
The affected products, the LANTIME M-Series, are NTP Servers. According to Meinberg, the Meinberg NTP Servers are deployed across several sectors including Commercial Facilities, Communications, Energy, Financial Services, and Transportation Systems. Meinberg estimates that these products are used primarily in the United States and Europe.
The web interface for LANTIME M-Series contains a flaw that allows a reflected cross-site scripting vulnerability.
This vulnerability could be exploited remotely.
EXISTENCE OF EXPLOIT
No known public exploits specifically target this vulnerability.
An attacker with a low skill would be able to exploit this vulnerability.
Meinberg’s firmware update, Version 6.15.020, resolves this vulnerability.
Please contact Meinberg customer service for information on how to download and install the firmware update, or obtain the update at the following online location:
ICS-CERT encourages asset owners to take additional defensive measures to protect against this and other cybersecurity risks.
- Minimize network exposure for all control system devices and/or systems, and ensure that they are not accessible from the Internet.
- Locate control system networks and remote devices behind firewalls, and isolate them from the business network.
- When remote access is required, use secure methods, such as Virtual Private Networks (VPNs), recognizing that VPNs may have vulnerabilities and should be updated to the most current version available. Also recognize that VPN is only as secure as the connected devices.
ICS-CERT also provides a section for control systems security recommended practices on the ICS-CERT web page at http://ics-cert.us-cert.gov/content/recommended-practices. Several recommended practices are available for reading and download, including Improving Industrial Control Systems Cybersecurity with Defense-in-Depth Strategies. ICS-CERT reminds organizations to perform proper impact analysis and risk assessment prior to deploying defensive measures.
Additional mitigation guidance and recommended practices are publicly available in the ICS‑CERT Technical Information Paper, ICS-TIP-12-146-01B—Targeted Cyber Intrusion Detection and Mitigation Strategies, that is available for download from the ICS-CERT web site (www.ics-cert.org).
Organizations observing any suspected malicious activity should follow their established internal procedures and report their findings to ICS-CERT for tracking and correlation against other incidents.
In addition, ICS-CERT recommends that users take the following measures to protect themselves from social engineering attacks:
1. Do not click web links or open unsolicited attachments in email messages.
2. Refer to Recognizing and Avoiding Email Scamsd for more information on avoiding email scams.
3. Refer to Avoiding Social Engineering and Phishing Attackse for more information on social engineering attacks.
- a. CWE-79: Improper Neutralization of Input During Web Page Generation ('Cross-site Scripting'), http://cwe.mitre.org/data/definitions/79.html, web site last accessed October 30, 2014.
- b. NVD, http://web.nvd.nist.gov/view/vuln/detail?vulnId=CVE-2014-5417, NIST uses this advisory to create the CVE web site report.
- c. CVSS Calculator, http://nvd.nist.gov/cvss.cfm?version=2&vector=AV:N/AC:L/Au:N/C:P/I:P/A:P, web site last accessed October 30, 2014.
- d. Recognizing and Avoiding Email Scams, http://www.us-cert.gov/reading_room/emailscams_0905.pdf, web site last accessed October 30, 2014.
- e. National Cyber Alert System Cyber Security Tip ST04-014, http://www.us-cert.gov/cas/tips/ST04-014.html, web site last accessed October 30, 2014.
For any questions related to this report, please contact ICS-CERT at:
Toll Free: 1-877-776-7585
International Callers: (208) 526-0900
For industrial control systems security information and incident reporting: http://ics-cert.us-cert.gov
ICS-CERT continuously strives to improve its products and services. You can help by choosing one of the links below to provide feedback about this product.